How to Choose Car Amplifier?

If you want your music to be loud, car audio amplifiers are definitely part of the picture. But an amplifier can do much more than just get other people's attention. Adding car audio amplifiers gives you a clean power source that can drive your speakers without straining. That means your music will sound cleaner and more defined at all volume levels.

Some features and aspects of Car Audio Amplifiers to consider are:

Bridgeable: This feature allows a pair of amplifier power channels to be combined into one channel of greater power. This is usually used for driving a subwoofer although it will work with any other type of speaker as well

Channels: The more channels car amplifiers have the greater the installation flexibility it will have. Especially in terms of options, future add-ons and upgrades.

Class: This refers to the way the amplifier operates. The three types that are most likely to be encountered are A, A/B, and D. Class A amplifiers are the least efficient in terms of power consumption, staying on continually, but also have better sound in general than A/B amplifiers. They are very rare in car audio. Class A/B amplifiers are more efficient than the class A design and are the most common type. Almost all amplifiers in the car audio market are of the A/B design. Class D amplifiers are usually reserved for high power subwoofer amplifiers and can reach efficiencies in the 80%+ range. This design can therefore be smaller, uses less current and produces less heat than the other classes.

Connectors: This is the method of attachment used for wires that are connected to the amplifier, including speaker and power wires. The most common kind is the screw terminal strip. This is a series of screw connectors that can be removed and replaced without compromising the amplifier. The other main type of attachment is the "Molex" type connector. This method involves a wire harness that plugs into the amplifier after the power and speaker connections have been made with a crimp or solder connection. If the amplifier is installed in more than one system these wires can get pretty short over time and become more difficult and even dangerous to work with. A variation on the two is a harness that the power and speaker wires screw into. Then the harness plugs into the amplifier. This is probably the most convenient of all connections.

Crossover/Filter: A built in crossover can be useful, especially if it is many frequencies of adjustment. A filter is a crossover that only affects one channel, not actually splitting frequencies but simply reducing a range of them.

Distortion: This is often given as T.H.D. or total harmonic distortion. It is the measure of how much an amplifier will change a signal from the input signal it is given. Figures below 0.1% are negligible and will not be heard. Usually the figure can be in the 3% range without being heard but virtually all high quality amplifiers will have a T.H.D. below 0.1%.

Efficiency: This is the ratio of of power input (from the battery) to power output (to the speakers). A 100 watt amplifier with an efficiency of 50% would take in 200 watts of power from the battery and output 100 watts of power to the speakers. The other 100 watts of power would be wasted as heat. The higher the efficiency of an amplifier the better.

Power Output: The rated power output of an amplifier should be given into a four ohm load, all channels driven from twenty to twenty thousand hertz (20Hz-20kHz). Keep in mind that while the low end amplifiers are exaggerated in their power output, many high end amplifiers are under-rated in their power output. These are sometimes called "cheater amps" because they allow a car audio competitor to compete in a lower power class while in reality having a larger amplifier. This under-rating can be three times less than the actual power output.

Power Supply: The two most common types are the IC chip and the MOSFET supply. The IC chip is what is used in most source units (head units) and are only capable of producing about twenty watts per channel. MOSFET is the more common design and has a smoother sound than the chip design.

Pre-amp Inputs: This is a set of jacks (usually RCA jacks) that will accept a low level pre-amp signal from a source or processing unit.

Pre-amp Outputs: This is a set of jacks (usually RCA jacks) that pass on a low level pre-amp signal to another amplifier or processing unit. These will sometimes be filtered outputs.


Separate Gain Controls: This allows the gain of each channel of the amplifier to be set independently of the other(s).

Speaker Level Inputs: For source units that do not have pre-amp level RCA outputs this feature may be used to take the signal from the speaker leads of the source unit. The signal will not be as clean as a pre-amp level output but will be adequate for most factory upgrade applications.

Stability: The measure of how low of an impedance load an amplifier can handle (in ohms). Any good quality amplifier will be two ohm stable while a rare few will go as low as a quarter of an ohm. Ideally an amplifier should double its power each time the load is halved. For example, a one hundred watt amplifier (into a four ohm load) should produce two hundred watts into a two ohm load and so on. This is most useful when running multiple speakers off of a single amplifier or in sound off competitions that are classed by total power output.

Tri-Mode Output: This feature is available under different names but is the ability of an amplifier to run a stereo pair of speakers and a mono subwoofer (or center channel) from only two channels of the amplifier. Personally, I would not recommend doing this. Instead buy a good quality four channel amplifier and bridge two of the channels for the subwoofer.

Tube Amplifiers: These are the least common amplifiers and are also the most expensive. Rather than the traditional solid state components they use old fashioned vacuum tubes. They are said to produce a warmer sound and a smoother midrange than solid state designs. For most systems the standard design will be more desirable.

Ok its time to say where I should buy my favorite Car Amplifier. I say look no more butwww.NetProAudo.net .they have variety Car Amplifiers at a very affordable prices. Go take a look for yourself and decide.

Good Luck..................